We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Cablenet FT-802S15 network media converter 100 Mbit/s 1310 nm Single-mode
SKU
FT802S15
Category: Network Media Converters
PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fibre to 10/100BASE-TX shielded twisted pair (STP) converter.
It supports both half-duplex and full-duplex operations and a variety of fibre options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port.
When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half-duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth.
An override switch provides total manual control over the half/full-duplex operation in a fibre-optic interface. The fibre port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.
Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard
Connectors: 1 x RJ45 (auto-MDI/MDI-X) twisted pair, EIA568
One fibre-optic, 1310nm wavelength, connector type and distance vary with model
FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm
FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm
Data Transfer Rate:
TP: 10/100Mbps
FX: 100Mbps
Duplex mode support:
Full or half-duplex mode by auto-negotiation (TP)
Full or half-duplex mode by DIP switch (FX)
LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
DIP switch: 2 DIP switches
Rear DIP switch: FX duplex mode selection
Side DIP switch: LFP (Link Fault Pass-through) mode selection
IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets
It supports both half-duplex and full-duplex operations and a variety of fibre options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port.
When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half-duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth.
An override switch provides total manual control over the half/full-duplex operation in a fibre-optic interface. The fibre port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.
Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard
Connectors: 1 x RJ45 (auto-MDI/MDI-X) twisted pair, EIA568
One fibre-optic, 1310nm wavelength, connector type and distance vary with model
FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm
FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm
Data Transfer Rate:
TP: 10/100Mbps
FX: 100Mbps
Duplex mode support:
Full or half-duplex mode by auto-negotiation (TP)
Full or half-duplex mode by DIP switch (FX)
LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
DIP switch: 2 DIP switches
Rear DIP switch: FX duplex mode selection
Side DIP switch: LFP (Link Fault Pass-through) mode selection
IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets
SKU | FT802S15 | ||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
EAN | 4711213680540 | ||||||||||||||||||||||||||||||||||||
Specification |
|
||||||||||||||||||||||||||||||||||||
Manufacturer | Cablenet | ||||||||||||||||||||||||||||||||||||
In Stock | Y |